Our concept and design for these products began in 1982 and spent
5 years in the development stage. This system is an add-on Hydrogen (HHO, Brown'sGas) generator that will transform
your standard vehicle into an all new, eco-friendly hybrid automobile. It is possible for you to realize a mileage increase
as high as 40% above your current MPG.
OUR PRODUCTS
Hydro Super2tm
Hydro Super2tmDouble
These systems are fully saturated, which means that the
unit is full of a water/hydrogen mix at all times. Previous obstacles to saturation have now been overcome through increased
testing and development.
HOW THE SYSTEM WORKS
The systems have a very low heat threshhold, reaching maximum
peak temperatures of 30 to 40 degrees over a ten hour use period.
The unit circulates the mix via a process known as thermal migration.
The process of thermal migration begins by transporting the gas via a tube into the main unit. The gas then rises via
a second tube, transporting the liquid mix. This circulation process, among other things, aids in the cooling of the
unit. The mix/separator tank serves as a storage area for the mix, as well as functions as a gas separator. It
dissipates heat and dislodges the hydrogen and oxygen bubbles, making this a completely self-contained unit.
SEPARATOR/ARRESTOR
By dislodging these bubbles, the bubble/flash arrestor
creates free space which allows for more production space on the plat surfaces. This means that the volume of hydrogen
is increased while using less power.
MIXES
These units use one of two mixes. You can use either
5% distilled white vinegar full strength or KOH and distilled water.
VINEGAR
Vinegar works well if you are able to create a strong enough
mix to produce a 8 to 9 amp cold draw.
KOH AND DISTILLED WATER
KOH is caustic, but it does not weaken, and it is far easier
to reach the 8/9 amp cold draw threshhold necessary for operation. You will also increase your output by as much as
10%. We recommend KOH for maximum production. You can find KOH sources by visiting www.braintan.com or www.fennerchemical.com.
When using KOH, the amp draw is determined by the strength
of the mixture. To get the correct cold amp draw, we suggest adding small amounts of KOH while testing the amps, increasing
the strength until you have reached a target operating strength of 9/10 cold amp draw. Maintenance requires that you
add distilled water to the mix between scheduled cleanings. Cleaning instructions are included further down on this
page.
SIZE
The Super2 is very compact. It is 12" tall by 3 1/4" wide.
The Super2 Double is 12" tall by 6 1/2" in width. The Super2 Double is equiped with a separate mix/separator and therefore
does not require a pump.
CARE OF THE UNIT
In freezing weather, add 1/2 cup methyl alcohol per 1 gallon
of mixed HEET GAS TREATMENT. This works to a maximum low temperature of 15 degrees farenheit. The unit must be
drained and removed from service for temperatures lower than 15 degrees. Remember that the more foreign substances other
than water introduced into the the lower the amount of Hydrogen produced. It will not however cause the unit to freeze.
SINGLE UNIT
The Super2 has been tested and produces +2 liters of hydrogen
per minute. The single unit amp draw is 16 amps HOT.
These tests were performed by the science department at
Ohio State University under normal operating conditions.
SUPER2 DOUBLE
The Super2 Double produces +3 LPM using vinegar.
Output is increased to +4.2 LPM using the recommended KOH mix. The amp draw for this unit is 14 to 16 amps per cell
HOT.
CONSTRUCTION
The main component is made of stainless steel 120 wall
and is approximately 1/8" thick. The ends are made of 3/4" high temperature reconstituted nylon end cap. Colors
for these units vary from black to an off white color.
The Double unit is comprised of two anodes, which are specially
designed and separated plates of stainless steel. They are then sealed with Nitrile O rings. The mix/separator
tank is custom blow molded. It is formed with mounting holes and is approzimately 3/8" thick. It is also equiped
with a pepcock for easy flush out and cleaning.
UNIT PARTS LIST
1. Main Hydro Super 2tm unit
2. Mix/ Separator tank
3. Connection tubing Red 3/8" id Blue
1/4" id
4. 5 feet # 10 awg copper wire (Pre wired to unit)X 2 on double cell
5. 10 feet # 16 awg copper wire
(Pre wired to unit)
6. Crimp on wire ends (pre installed)
7. 30 amp relay (Pre wired and mounted to unit)X2
on double cell
8. 30 amp fuse holder and fuse (Pre assembled into the# 10 wire)
X2 on double cell
9. Lighted dash switch (Pre wired and ready to mount)
10. Special 90 used to connect to air tube
11. Complete instructions
12. 1 Powered By Hydro Super
2 Bumper Sticker
Almost all gas fuel injected vehicles will need at minimum an O2 sensor extender to
see the benefits from the HYDRO SUPER 2. That is because the unit puts more oxygen into the engine, and your O2 sensor will
see that extra Oxygen. Sometimes that will tell the computer that the engine is running a lean mixture. It will then up the
fuel ratio, blanking out the GAINS that the Hydro super 2 is giving you!. This problem is solved by installing a O2
sensor extender. This backs the O2 sensor out of the exhaust pipe 3/4 inch so it does not see the extra oxygen. In doing that
your engine leans it self down and you see the full benefits of the HYDRO SUPER 2. The extenders work on app 80 % of the vehicles.
The other 20% will need what is called an EFIE to get any HHO generator to work. The EFIEs are available from www.fuelsaver-mpg.com. Some Toyota's have AFR sensors which will require that you check with fuel saver for viable options in
installation. These units require about 2 hours to install.
INSTALLATION INSTRUCTIONS
1. Mount the main HYDRO SUPER 2 unit.
2. Mount the Mix/Separator tank. Connect the blue tube between the bottom of the Mix/Separator
tank to the bottom of the HYDRO SUPER 2.
3. Connect the red tube to the top of the HYDRO SUPER 2 to the side fitting on the mix
tank.
4. Connect the remaining red tube from the top of the Mix/Separator tank to the air intake of
your vehicle. See diagram in instructions for locations.
THESE UNITS COME COMPLETELY ASSEMBLED AND WIRED. The
following instructions are included for mounting the unit to your vehicle.
1. CONNECT THE HOSES BETWEEN THE UNITS
And 1 HOSE TO AIR INTAKE OF YOUR VEHICLE.
2.HOOK UP 4 WIRES (6 wires on the double cell).
3. Start your vehicle and turn on your dash switch.
4. Watch the flow of the HHO in the red line between the main unit
and the Mix/Separator tank. You will be AMAZED at what you see!!
The Hydro Super 2 and Hydro Super 2 Double units will work on fuel injected/carburetor
or diesel engines.
The Super Hydro 2 WORKS ON ENGINES UP TO A 3.8 LTR.
We also have
a DOUBLE unit for larger engines.
CHECK OUR PAGE (WILL IT WORK ON MY CAR ) for recommended usage and for engines.
Don't be scared by the price. This unit is commercial grade. Our Units carry a 45 day Satisfaction guarantee and 1 year guarantee/warantee
on materials and workmanship. For warranty ship unit postage paid back to us and we will repair or replace unit and ship it
back to you postage paid .
There is NO guarantee that your vehicle will see gains from a HHO generator
due to driving habits and the way the computer on your vehicle may or may not work with the unit.
The dealer, maufacturer, and assignees make no guarantees as to fitness for a particular purpose.
This equipment is classed as experimental. The Consumer/buyer assumes all risks and liabilities arising from the installation/use
of this equipment.
Hydro Fuel Solutions and it's dealers and/or assignees shall not be held liable for
damage to property or for injury to persons up to and including death as a result of the installation and use of this product.
The purchase of this product shall create a hold harmless agreement between the buyer, Hydro Fuel Solutions, and all of its
agents. Purchaser assumes ALL risk associated with the installation and use of this product.